Caracterização mecânica e microestrutural do aço MARAGING 300, soldado a plasma e submetidas a reparos

Carregando...
Imagem de Miniatura

Data

2014-06-25

Autores

Silva, Deivid Ferreira da [UNESP]

Título da Revista

ISSN da Revista

Título de Volume

Editor

Universidade Estadual Paulista (Unesp)

Resumo

This study aims to evaluate and quantify the possible losses of mechanical resistance in the welded join of MARAGING 300 steel submitted within three after repairs in the cords of the welded. The Institute of Aeronautics and Space (IAE) designs, develops and manufactures sounding rockets and satellite launcher vehicles (VLS) using solid propellant and the motor case is responsible for supporting the pressure during the burning of this propellant. Currently, the motor case is made of 300M-ESR steel. Due to a number of advantages found in the mechanical properties and the manufacturing process, IAE is studying the replacement of 300M-ESR steel by MARAGING 300 steel. The welding method used for achievement of the work was the process of plasma arc welding (paw) in a single pass, using the keyhole technique with filler metal. The welded joints are evaluated by adopting non-destructive testing acceptance criteria according to AWS D17.1. In this work, the repairs were done, manually, using the tungsten inert gas method (TIG). Measures of mechanical strength, Vickers hardness (HV), chemical analysis, metallographic analysis and fractography of the welded joint were made at the various welding conditions. The results show that after welding and repair and before the aging heat treatment the adjacent region to the weld fusion zone have hardness lower than other regions affected thermally. It is due to segregation of solute in the region. After aging treatment there is an increase in levels of hardness of about 200HV, but the fusion zone and near the weld zone with hardness remain slightly lower than the rest of the material. The analyzes of the fractured surface showed that the rupture of the specimens occurred in the region of the heat affected zone near the weld , and has a appearance of mixed fractures with formation predominantly of microvoid (dimples) ... (Complete abstract click electronic access below)
Este trabalho tem como objetivo avaliar e quantificar as possíveis perdas na resistência mecânica da junta soldada de aço MARAGING 300, após a realização de até três reparos no cordão da solda. O Instituto de Aeronáutica e Espaço (IAE) projeta, desenvolve e fabrica foguetes de sondagem e veículos lançadores de satélites (VLS) utilizando propelente sólido e o envelope metálico é o responsável por suportar a pressão de trabalho durante a queima deste propelente. Atualmente o envelope motor é fabricado em aço 300M-ESR e, devido a uma série de vantagem nas propriedades mecânicas encontradas e no processo de confecção, o IAE estuda a substituição do aço 300M-ESR pelo aço MARAGING 300. O método de soldagem utilizado para a realização do trabalho foi o processo de soldagem a plasma (PLASMA ARC WELDING – PAW) em passe único, utilizando-se a técnica keyhole com metal de adição. Estas juntas soldadas são avaliadas por ensaios não destrutivos, adotando critérios de aceitação de acordo com a norma AWS D17.1. Neste trabalho, a confecção dos reparos foi feita de forma manual, utilizando o método TIG (TUNGSTEN INERT GAS). Foram realizadas as avaliações de resistência mecânica, perfil de dureza Vickers (HV) por microindentações, análises químicas, análises metalográficas e fractográficas da junta soldada nas diversas condições de soldagem. Os resultados mostram que após a solda e reparos, antes do tratamento térmico de envelhecimento, a região fundida e a região adjacente à solda apresentam uma dureza abaixo das outras regiões afetadas termicamente, isto se deve a segregação de solutos na região. Com o envelhecimento há uma elevação nos níveis de dureza de cerca de 200HV, porém a zona fundida e a zona próxima à solda permanece com uma dureza um pouco inferior ao restante do material. As anális... (Resumo completo, clicar acesso eletrônico abaixo)

Descrição

Palavras-chave

Aço de alta resistencia, Resistência à tração, Soldagem, Juntas soldadas, Soldagem eletrica, Metalografia, Welding

Como citar

SILVA, Deivid Ferreira da. Caracterização mecânica e microestrutural do aço MARAGING 300, soldado a plasma e submetidas a reparos. 2014. 112 f. Dissertação (mestrado) – Universidade Estadual Paulista, Faculdade de Engenharia de Guaratinguetá, 2014.