Implementação de um aparato experimental para medição de instabilidade em superfície livre com fluido não-Newtoniano
Carregando...
Arquivos
Data
2018-07-31
Autores
Cunha, Evandro Fernandes da
Título da Revista
ISSN da Revista
Título de Volume
Editor
Universidade Estadual Paulista (Unesp)
Resumo
Esta tese de doutorado traz uma abordagem experimental sobre mecanismos de geração, desenvolvimento e propagação em canal de instabilidade na superfície livre de um escoamento de fluido não-Newtoniano. Estas instabilidades, quando evoluem para um padrão estável, exibem comprimento, amplitude e celeridade bem definidos, sendo denominadas roll waves. Na literatura existe uma lacuna no que diz respeito às medições destes fenômenos em condições controladas de laboratório, e com pouquíssimos registros, quando presentes em eventos naturais. Assim, buscou-se neste trabalho projetar e implementar um aparato experimental operacional e de baixo custo com o objetivo de gerar e aferir tais instabilidades, sob condições controladas e sem a influência de vibrações externas (canalete posicionado sobre uma mesa inercial), seguindo metodologia de ensaio proposta e testada. O fluido teste utilizado foi o gel de carbopol 996, que apresentou boa estabilidade e propriedades reológicas aderentes ao modelo de Herschel-Bulkley, tal qual as lamas encontradas em pés de barragens, lamas oriundas de fluxos hiperconcentrados ou de corridas propriamente ditas. Um sistema de sucção-recalque, através de uma bomba hidráulica de cavidade progressiva, impulsionava o gel para o canal de ensaio, garantindo fluxo contínuo do material em regime de recirculação. Para gerar as instabilidades na superfície livre, foi imposta, a montante do canal, uma perturbação, por meio de um pulso de ar controlado em intensidade e frequência. Após evolução e estabilização, a onda (roll wave) era aferida por meio de sistema de medição ultrassônico na configuração de pulso-eco e, seguindo metodologia inovadora proposta nesta tese, por meio de técnica fotométrica em função da absorção luminosa de um corante (azul de metileno) adicionado ao fluido teste em escoamento. Para confirmação da qualidade dos resultados obtidos pela aplicação das técnicas de medição experimental, foram feitas confrontações entre as técnicas experimentais propostas e entre estas e um modelo numérico, desenvolvido pelo grupo de pesquisa. Por fim, foram testados dois estudos de caso de formação e propagação de roll waves no canal, o primeiro visando a obtenção e tratamento das amplitudes em diversos pontos ao longo do canal, e, no segundo, a influência da frequência de perturbação sobre a amplitude da roll wave, todos para cenários experimentais com números de Froude superiores ao Froude mínimo, condição necessária à geração do fenômeno.
This doctoral thesis brings an experimental approach on generation, development and propagation mechanisms of instabilities free-surface flows of a non-Newtonian fluid. When these instabilities evolve to a stable pattern, they display well-defined length, amplitude and celerity, being denominated as roll waves. There is a great gap in literature concerning experimental data. Few experiments are found relating laboratory measurements of these phenomena in controlled conditions; this is also true when it comes to in situ measurements from natural events. Thus, the aim of this project was to design and implement a low cost operational experimental apparatus to generate and measure such instabilities under controlled conditions, isolated from external vibration influences. This project follows a previous methodology developed which was tested and approved. Carbopol gel 996 was used as test fluid, presenting good stability and rheological properties matching to Herschel-Bulkley model, oftenly used for modeling industrial sludge, slurry fluids, natural mud, among others. A hydraulic circuit was installed in which a progressive cavity hydraulic pump pushed the gel to the inlet of the testing channel, ensuring continuous flow of material, capturing the fluid at the channel outlet. A free-surface disturbance was imposed to the flow through a controlled pulse of air (intensity and frequency) on the upstream flow to produce the free-surface instabilities. After evolution and stabilization, the wave (roll wave) was measured through ultrasonic measurement system in the pulse-echo configuration and also through photometric technique using light absorption by a dye (methylene blue) added to the test fluid. Confrontations of the experimental data were made among the proposed experimental techniques and also with numerical simulations developed by the research group in order to assess the quality of the results obtained by the application of the experimental measurement techniques. Lastly, two case studies of formation and propagation of roll waves were tested: the first one aimed to obtain and process the amplitudes in several points along the channel; the second one, the influence of frequency of disturbance over the amplitude of the roll wave was studied. All the experimental scenarios were tested for Froude number over the minimum value necessary for the generation of the phenomenon.
This doctoral thesis brings an experimental approach on generation, development and propagation mechanisms of instabilities free-surface flows of a non-Newtonian fluid. When these instabilities evolve to a stable pattern, they display well-defined length, amplitude and celerity, being denominated as roll waves. There is a great gap in literature concerning experimental data. Few experiments are found relating laboratory measurements of these phenomena in controlled conditions; this is also true when it comes to in situ measurements from natural events. Thus, the aim of this project was to design and implement a low cost operational experimental apparatus to generate and measure such instabilities under controlled conditions, isolated from external vibration influences. This project follows a previous methodology developed which was tested and approved. Carbopol gel 996 was used as test fluid, presenting good stability and rheological properties matching to Herschel-Bulkley model, oftenly used for modeling industrial sludge, slurry fluids, natural mud, among others. A hydraulic circuit was installed in which a progressive cavity hydraulic pump pushed the gel to the inlet of the testing channel, ensuring continuous flow of material, capturing the fluid at the channel outlet. A free-surface disturbance was imposed to the flow through a controlled pulse of air (intensity and frequency) on the upstream flow to produce the free-surface instabilities. After evolution and stabilization, the wave (roll wave) was measured through ultrasonic measurement system in the pulse-echo configuration and also through photometric technique using light absorption by a dye (methylene blue) added to the test fluid. Confrontations of the experimental data were made among the proposed experimental techniques and also with numerical simulations developed by the research group in order to assess the quality of the results obtained by the application of the experimental measurement techniques. Lastly, two case studies of formation and propagation of roll waves were tested: the first one aimed to obtain and process the amplitudes in several points along the channel; the second one, the influence of frequency of disturbance over the amplitude of the roll wave was studied. All the experimental scenarios were tested for Froude number over the minimum value necessary for the generation of the phenomenon.
Descrição
Palavras-chave
Roll waves, Fluidos não-Newtonianos, Técnicas fotométricas, Técnicas ultrassônicas, Superfície livre, Non-Newtonian fluids, Photometric Techniques, Ultrasonic Techniques, Free Surface