Show simple item record

dc.contributor.authorMachado, Ana Lucia [UNESP]
dc.contributor.authorBreeding, L. C.
dc.contributor.authorPuckett, A. D.
dc.date.accessioned2014-05-20T13:46:19Z
dc.date.available2014-05-20T13:46:19Z
dc.date.issued2005-08-01
dc.identifierhttp://dx.doi.org/10.1016/j.prosdent.2005.04.017
dc.identifier.citationJournal of Prosthetic Dentistry. St Louis: Mosby, Inc., v. 94, n. 2, p. 183-189, 2005.
dc.identifier.issn0022-3913
dc.identifier.urihttp://hdl.handle.net/11449/16377
dc.description.abstractStatement of problem. Microwave irradiation has been suggested for denture disinfection. However, the effect of this procedure on the hardness and bond strength between resilient liners and denture base acrylic resin is not known.Purpose. This study evaluated the effect of water storage time and microwave disinfection on the hardness and peel bond strength of 2 silicone resilient lining materials to a heat-polymerized acrylic resin.Material and methods. Acrylic resin (Lucitone 199) specimens (75 X 10 X 3 mm) were stored in water at 37 degrees C (2 or 30 days) before bonding (n = 160). The resilient lining materials (GC Reline Extra Soft and Dentusil) were bonded to the denture base and divided into the following 4 groups (n = 10): Tests performed immediately after bonding (control); specimens immersed in water (200 mL) and irradiated twice, with 650 W for 6 minutes; specimens irradiated daily for 7 total cycles of disinfection; specimens immersed in water (37 degrees C) for 7 days. Specimens were submitted to a 180-degree peel test (at a crosshead speed of 10 mm/min) and the failure values (MPa) and mode of failure were recorded. Pretreatment and posttreatment hardness measurements (Shore A) of the resilient materials were also performed. Three-way analysis of variance, followed by the Tukey HSD test, was performed (alpha=.05).Results. The analysis revealed that, for all conditions, the mean failure strengths of GC Reline Extra Soft (0.95-1.19 MPa) were significantly higher (P<.001) than those of Dentusil (0.45-0.50 MPa). The adhesion of the liners was not adversely affected by water storage time of Lucitone 199 or microwave disinfection. All peel test failures were cohesive. There was a small but significant difference (P<.001) between the pretreatment (34.33 Shore A) and posttreatment (38.69 Shore A) hardness measurements.Conclusion. Microwave disinfection did not compromise the hardness of either resilient liners or their adhesion to the denture base resin Lucitone 199.en
dc.format.extent183-189
dc.language.isoeng
dc.publisherMosby, Inc
dc.relation.ispartofJournal of Prosthetic Dentistry
dc.sourceWeb of Science
dc.titleEffect of microwave disinfection on the hardness and adhesion of two resilient linersen
dc.typeArtigo
dcterms.licensehttp://www.elsevier.com/about/open-access/open-access-policies/article-posting-policy
dcterms.rightsHolderMosby, Inc
dc.contributor.institutionUniversidade Estadual Paulista (Unesp)
dc.contributor.institutionUniversity of Mississippi
dc.description.affiliationUNESP, Fac Odontol Araraquara, Araraquara Dent Sch, Dept Dent Mat & Prosthodont, BR-14801903 São Paulo, Brazil
dc.description.affiliationUniv Mississippi, Med Ctr, Sch Dent, Jackson, MS 39216 USA
dc.description.affiliationUnespUNESP, Fac Odontol Araraquara, Araraquara Dent Sch, Dept Dent Mat & Prosthodont, BR-14801903 São Paulo, Brazil
dc.identifier.doi10.1016/j.prosdent.2005.04.017
dc.identifier.wosWOS:000230994200010
dc.rights.accessRightsAcesso restrito
unesp.campusUniversidade Estadual Paulista (Unesp), Faculdade de Odontologia, Araraquarapt
dc.identifier.lattes8000248781842587
unesp.author.lattes8000248781842587[1]
unesp.author.orcid0000-0002-2718-428X[1]
dc.relation.ispartofjcr2.347
dc.relation.ispartofsjr1,087
Localize o texto completo

Files in this item

FilesSizeFormatView

There are no files associated with this item.

This item appears in the following Collection(s)

Show simple item record