Comparison of accuracy between compression- and injection-molded complete dentures

Página do item simplificado
dc.contributor.authorNogueira, S. S.
dc.contributor.authorOgle, R. E.
dc.contributor.authorDavis, E. L.
dc.contributor.institutionSUNY Buffalo
dc.contributor.institutionUniversidade Estadual Paulista (Unesp)
dc.date.accessioned2014-05-20T15:23:51Z
dc.date.available2014-05-20T15:23:51Z
dc.date.issued1999-09-01
dc.description.abstractStatement of problem. A clinically significant incisal pin opening may occur after processing complete dentures if a compression molding technique is used. To recover the proper vertical dimension of occlusion, a time-consuming occlusal adjustment is necessary that often destroys the anatomy of the artificial teeth. A new injection molding process claims to produce dentures that require few, if any, occlusal adjustments in the laboratory after processing.Purpose. This laboratory study compared incisal pin opening, dimensional accuracy, and laboratory working time for dentures fabricated by this new injection system with dentures constructed by the conventional compression molding technique.Material and methods. Two groups of 6 maxillary and 6 mandibular dentures were evaluated as follows: group 1 (control), Lucitone 199, compression molded with a long cure cycle; and group 2, Lucitone 199, injection molded with a long cure. Incisal pin opening was measured with a micrometer immediately after deflasking. A computerized coordinate measuring machine was used to measure dimensional accuracy of 3-dimensional variations in selected positions of artificial teeth in 4 stages of denture fabrication. Analysis of variance (ANOVA) and t tests were performed to compare the groups.Results. A significant difference was found in pin opening between groups (t test). Horizontal dimensional changes evaluated with repeated measures ANOVA revealed no significant differences between groups. However, analysis of vertical dimensional changes disclosed significant differences between the groups. There was no appreciable difference in laboratory working time for flasking and molding denture bases between the injection and compression molding techniques when polymethyl methacrylate resin was used.Conclusion. The injection molding method produced a significantly smaller incisal pin opening over the standard compression molding technique. The injection molding technique, using polymethyl methacrylate, was a more accurate method for processing dentures. There were no appreciable differences in laboratory working time between the injection and compression molding techniques.en
dc.description.affiliationSUNY Buffalo, Sch Dent Med, Dept Restorat Dent, Buffalo, NY 14260 USA
dc.description.affiliationSUNY Buffalo, Sch Dent Med, Dept Oral Hlth Serv & Informat, Buffalo, NY 14260 USA
dc.format.extent291-300
dc.identifierhttp://dx.doi.org/10.1016/S0022-3913(99)70083-1
dc.identifier.citationJournal of Prosthetic Dentistry. St Louis: Mosby-year Book Inc., v. 82, n. 3, p. 291-300, 1999.
dc.identifier.doi10.1016/S0022-3913(99)70083-1
dc.identifier.issn0022-3913
dc.identifier.urihttp://hdl.handle.net/11449/34541
dc.identifier.wosWOS:000082837700010
dc.language.isoeng
dc.publisherMosby-year Book Inc
dc.relation.ispartofJournal of Prosthetic Dentistry
dc.relation.ispartofjcr2.347
dc.relation.ispartofsjr1,087
dc.rights.accessRightsAcesso restrito
dc.sourceWeb of Science
dc.titleComparison of accuracy between compression- and injection-molded complete denturesen
dc.typeArtigo
dcterms.licensehttp://www.elsevier.com/about/open-access/open-access-policies/article-posting-policy
dcterms.rightsHolderMosby-year Book Inc

Arquivos

Licença do Pacote
Agora exibindo 1 - 1 de 1
Nenhuma Miniatura disponível
Nome:
license.txt
Tamanho:
1.71 KB
Formato:
Item-specific license agreed upon to submission
Descrição:

Coleções

Artigos