Publicação:
Physical characteristics of oily spraying liquids and droplets formed on coffee leaves and glass surfaces

dc.contributor.authorDecaro, Sergio T.
dc.contributor.authorFerreira, Marcelo Da C.
dc.contributor.authorLasmar, Olinto
dc.contributor.institutionFCAV
dc.date.accessioned2021-07-14T10:21:12Z
dc.date.available2021-07-14T10:21:12Z
dc.date.issued2015
dc.description.abstractThe physical characteristics of a spray liquid are important in getting a good droplet formation and control efficiency over a particular target. As a function of these characteristics, it is possible to decipher which is the best adjuvant based on the respective concentration used during the spray. Therefore, ten spraying liquids were prepared, which varied in concentrations of pesticide lufenuron + profenofos, mineral oil, water and manganese sulfate. Pendant droplets formed from these mixtures were measured to examine their impact on surface tension. Droplets were applied to the surface of coffee leaves and the surface tension, contact angle formed and the leaf area wetted by the droplet, were measured. A smooth glass surface was taken as a comparative to the coffee leaves. The highest concentrations of oil resulted in lower surface tension, smaller contact angles of droplets on leaf surfaces and larger areas wetted by the droplets. Both surfaces showed hydrophilic behavior.en
dc.description.abstractAs características físicas da calda de pulverização são importantes para que haja boa formação de gotas e eficiência de controle sobre determinado alvo. Em função dessas características, pode-se decidir sobre qual o melhor adjuvante, em sua respectiva concentração, poderá ser utilizado durante a pulverização. Para tanto, foram preparadas dez caldas fitossanitárias em que variaram as concentrações do inseticida lufenuron + profenofós, óleo mineral, água e sulfato de manganês. Gotas pendentes formadas a partir dessas misturas foram medidas em sua tensão superficial. Aplicaram-se gotas sobre a superfície de folhas de café e foram medidos a tensão superficial, o ângulo de contato formado e a área da folha molhada pela gota. Uma superfície lisa de vidro foi tomada como comparativo às folhas de café. As maiores concentrações de óleo resultaram em menores valores de tensão superficial, menores ângulos de contato de gotas com a superfície foliar e maiores áreas molhadas pelas gotas. Ambas as superfícies mostraram-se hidrofílicas.pt
dc.description.affiliationFCAV, Departamento de Fitossanidade
dc.format.extent588-600
dc.identifierhttp://dx.doi.org/10.1590/1809-4430-Eng.Agric.v35n3p588-600/2015
dc.identifier.citationEngenharia Agrícola. Associação Brasileira de Engenharia Agrícola, v. 35, n. 3, p. 588-600, 2015.
dc.identifier.doi10.1590/1809-4430-Eng.Agric.v35n3p588-600/2015
dc.identifier.fileS0100-69162015000300588.pdf
dc.identifier.issn1809-4430
dc.identifier.issn0100-6916
dc.identifier.scieloS0100-69162015000300588
dc.identifier.urihttp://hdl.handle.net/11449/211226
dc.language.isoeng
dc.publisherAssociação Brasileira de Engenharia Agrícola
dc.relation.ispartofEngenharia Agrícola
dc.rights.accessRightsAcesso aberto
dc.sourceSciELO
dc.subjectsurface tensionen
dc.subjectcontact angleen
dc.subjectwetted areaen
dc.subjectoilen
dc.subjecttensão superficialpt
dc.subjectângulo de contatopt
dc.subjectárea molhadapt
dc.subjectóleopt
dc.titlePhysical characteristics of oily spraying liquids and droplets formed on coffee leaves and glass surfacesen
dc.title.alternativeCaracterísticas físicas de caldas oleosas e de gotas formadas em superfície de folhas de café e de vidropt
dc.typeArtigo
dspace.entity.typePublication

Arquivos

Pacote Original

Agora exibindo 1 - 1 de 1
Carregando...
Imagem de Miniatura
Nome:
S0100-69162015000300588.pdf
Tamanho:
310.54 KB
Formato:
Adobe Portable Document Format

Coleções