Publicação:
Influence of microwave disinfection on the dimensional stability of intact and relined acrylic resin denture bases

dc.contributor.authorSeo, Rosangela Seiko
dc.contributor.authorVergani, Carlos Eduardo [UNESP]
dc.contributor.authorPavarina, Ana Claudia [UNESP]
dc.contributor.authorCompagnoni, Marco Antonio [UNESP]
dc.contributor.authorMachado, Ana Lucia [UNESP]
dc.contributor.institutionUniversidade Estadual Paulista (Unesp)
dc.date.accessioned2014-05-20T13:46:17Z
dc.date.available2014-05-20T13:46:17Z
dc.date.issued2007-09-01
dc.description.abstractStatement of problem. Microwave irradiation has been suggested as a method to disinfect denture bases. However, the effect of microwave heating on the dimensional stability of the relined denture bases is unknown.Purpose. The purpose of this study was to evaluate the dimensional stability of intact and relined acrylic resin denture bases after microwave disinfection.Material and methods. A standard brass cast simulating an edentulous maxillary arch was machined and used to fabricate 2- and 4-mm-thick denture bases (n=200), which were processed with heat-polymerized acrylic resin (Lucitone 550). The 2-mm thick-specimens (n=160) were relined with 2 mm of autopolymerizing resin (Tokuso Rebase Fast, Ufi Gel Hard, Kooliner, or New Truliner). Distances between 5 removable pins on the standard brass cast were measured with a Nikon optical comparator, and the area (mm(2)) formed by the distance between 5 pins was calculated and served as baseline. During fabrication, the pins were transferred to the intaglio surface of the specimens. Differences between the baseline area and those subsequently determined for the specimens were used to calculate the percent dimensional changes. The intact and relined denture bases were divided into 4 groups (n=10) and evaluated after: polymerization (control group P); 1 cycle of microwave disinfection (MW); daily microwave disinfection for 7 days (control group MW7); water storage for 7 days (WS7). Microwave irradiation was performed for 6 minutes at 650 W. Data were analyzed using 2-way ANOVA followed by Tukey's test (alpha=.05).Results. Intact specimens and those relined with Kooliner and New Truliner showed increased shrinkage after 1 (P=.05, .018, and .001, respectively) and 7 (P <.001, .003, and <.001, respectively) cycles of microwave disinfection. With the exception of specimens relined with Kooliner, intact specimens showed greater shrinkage than the relined specimens after 7 cycles of microwave disinfection.Conclusions. Microwave disinfection produced increased shrinkage of intact specimens and those relined with New Truliner and Kooliner.en
dc.description.affiliationUniv Estadual Paulista, São Paulo State Univ, Fac Odontol Araraquara,Araraquara Dent Sch, Dept Dent Mat & Prosthodont, BR-14801903 São Paulo, Brazil
dc.description.affiliationUnespUniv Estadual Paulista, São Paulo State Univ, Fac Odontol Araraquara,Araraquara Dent Sch, Dept Dent Mat & Prosthodont, BR-14801903 São Paulo, Brazil
dc.format.extent216-223
dc.identifierhttp://dx.doi.org/10.1016/S0022-3913(07)60058-4
dc.identifier.citationJournal of Prosthetic Dentistry. New York: Mosby-elsevier, v. 98, n. 3, p. 216-223, 2007.
dc.identifier.doi10.1016/S0022-3913(07)60058-4
dc.identifier.issn0022-3913
dc.identifier.lattes3003130522427820
dc.identifier.lattes8867670539105403
dc.identifier.lattes8921196002764597
dc.identifier.lattes8000248781842587
dc.identifier.orcid0000-0002-7375-4714
dc.identifier.urihttp://hdl.handle.net/11449/16361
dc.identifier.wosWOS:000250155900007
dc.language.isoeng
dc.publisherElsevier B.V.
dc.relation.ispartofJournal of Prosthetic Dentistry
dc.relation.ispartofjcr2.347
dc.relation.ispartofsjr1,087
dc.rights.accessRightsAcesso restrito
dc.sourceWeb of Science
dc.titleInfluence of microwave disinfection on the dimensional stability of intact and relined acrylic resin denture basesen
dc.typeArtigo
dcterms.licensehttp://www.elsevier.com/about/open-access/open-access-policies/article-posting-policy
dcterms.rightsHolderElsevier B.V.
dspace.entity.typePublication
unesp.author.lattes3003130522427820[2]
unesp.author.lattes8867670539105403[3]
unesp.author.lattes8921196002764597
unesp.author.lattes8000248781842587[5]
unesp.author.orcid0000-0002-7375-4714[2]
unesp.author.orcid0000-0002-9231-1994[3]
unesp.author.orcid0000-0002-2718-428X[5]
unesp.campusUniversidade Estadual Paulista (UNESP), Faculdade de Odontologia, Araraquarapt
unesp.departmentMateriais Odontológicos e Prótese - FOARpt

Arquivos

Licença do Pacote

Agora exibindo 1 - 1 de 1
Nenhuma Miniatura disponível
Nome:
license.txt
Tamanho:
1.71 KB
Formato:
Item-specific license agreed upon to submission
Descrição: