Estudo das propriedades mecânicas em união de aços dissimilares soldadas pelo processo a plasma e a laser
Carregando...
Arquivos
Data
2018-07-27
Autores
Silva, Deivid Ferreira da [UNESP]
Título da Revista
ISSN da Revista
Título de Volume
Editor
Universidade Estadual Paulista (Unesp)
Resumo
O objetivo deste trabalho é avaliar e comparar a resistência mecânica da união de aços dissimilares, o aço Maraging 300 com o aço 300M-ESR pelos processos de soldagens autógenas a Plasma (Plasma Arc Welding – PAW) e a Laser (Laser Beam Welding – LBW). As juntas foram submetidas à avaliação da resistência mecânica através de ensaios de tração e de dureza Vickers (HV) no cordão de solda e zona termicamente afetada. Foram também realizadas análises químicas e metalográficas das juntas soldadas, correlacionando a microestrutura com as propriedades observadas. Em ambos os processos foram aplicados tratamentos térmicos antes e após as soldagens, com o objetivo de endurecer os materiais e procurando aproximar a dureza de ambos os aços e da zona fundida (ZF) e zona termicamente afetada pelo calor (ZTA). Foram realizados vários testes com tempos e temperaturas para se definir quais eram os melhores tratamentos térmicos adotados para a equalização das propriedades mecânicas. Os tratamentos térmicos aplicados após a solda mostraram-se convenientes para o nivelamento dos valores das durezas, somente exibindo poucas perdas nas ZTAs dos aços Maraging. Com a aplicação destes tratamentos também foi possível notar uma equalização nas resistências à tração, em torno de 1300 MPa e aumentos consideráveis das mesmas, comparado com a mesma condição sem tratamento. As soldas mostraram-se eficientes para a união das chapas, porém, em algumas situações da soldagem a Laser, apresentou pequenas falhas, presença de poros, nos cordões das soldas, com isso contribuindo para a diminuição do limite da resistência à tração.
The objective of this work is to evaluate and compare the mechanical strength of welded joints made of the dissimilar steels such as Maraging 300 steel with 300M-ESR steel by the autogenous Plasma Arc Welding (PAW) and Laser welding process (LBW). The joints were submitted to the mechanical strength evaluation by tensile test and hardness Vickers (HV) at the weld bead and thermally affected zone. Chemical analysis and metallographic analysis of the welded joints were also performed, correlating the microstructure observed with the properties. In both processes, heat treatments were applied before and after welding, with the objective of at harden the materials and seeking to approximate the hardness of both steels and the fusion zone and heat affected zone. Several tests were carried using different times and temperatures to determine which ones were the best heat treatments to be adopted aiming the equalization of mechanical properties. The heat treatments applied after welding proved to be convenient for the leveling of the hardness values, only showing few losses in the HAZs of the Maraging steels. Applying of these treatments, it was also possible to note the equalization of tensile strengths, around 1300 MPa and considerable increases of the same, compared to the same condition without treatment. The welds showed to be efficient for the joining of the plates, however, in some situations the Laser welding presented small flaws, such as presence of pores, in the weld beads, causing to the reduction of the tensile strength limit.
The objective of this work is to evaluate and compare the mechanical strength of welded joints made of the dissimilar steels such as Maraging 300 steel with 300M-ESR steel by the autogenous Plasma Arc Welding (PAW) and Laser welding process (LBW). The joints were submitted to the mechanical strength evaluation by tensile test and hardness Vickers (HV) at the weld bead and thermally affected zone. Chemical analysis and metallographic analysis of the welded joints were also performed, correlating the microstructure observed with the properties. In both processes, heat treatments were applied before and after welding, with the objective of at harden the materials and seeking to approximate the hardness of both steels and the fusion zone and heat affected zone. Several tests were carried using different times and temperatures to determine which ones were the best heat treatments to be adopted aiming the equalization of mechanical properties. The heat treatments applied after welding proved to be convenient for the leveling of the hardness values, only showing few losses in the HAZs of the Maraging steels. Applying of these treatments, it was also possible to note the equalization of tensile strengths, around 1300 MPa and considerable increases of the same, compared to the same condition without treatment. The welds showed to be efficient for the joining of the plates, however, in some situations the Laser welding presented small flaws, such as presence of pores, in the weld beads, causing to the reduction of the tensile strength limit.
Descrição
Palavras-chave
Aço maraging, Aço 300M, Solda a laser (LBW), Solda plasma (PAW), Maraging steel, Dissimilar welding, 300M Steel, Laser welding (LBW), Plasma welding (PAW)