Caracterização das ligas Ni-Ti-Mo, Ni-Ti-Ta e Ni-Ti-Mo-Zr obtidas por moagem de alta energia e prensagem a quente

Carregando...
Imagem de Miniatura

Data

2011-07-21

Autores

Pereira, Gilda Maria Cortez [UNESP]

Título da Revista

ISSN da Revista

Título de Volume

Editor

Universidade Estadual Paulista (Unesp)

Resumo

O Brasil ainda não produz a liga Ni – Ti em escala comercial, importando grande parte dos produtos à base de Ni – Ti voltados à área médica. O grande custo envolvido na importação destes produtos estimula a tentativa de desenvolvimento nacional desta liga. Assim, esta pesquisa objetivou a caracterização de ligas Ni-Ti-Mo, Ni-Ti-Ta e Ni-Ti-Mo-Zr produzidas por meio de moagem de alta energia e subseqüente prensagem a quente. A caracterização dos produtos moídos e prensados a quente foi realizada por meio de microscopia eletrônica de varredura, difração de raios X, espectrometria por dispersão de energia. Os resultados indicaram que a formação dos compostos intermetálicos, como o Ni3Ti, NiTi e NiTi2, ocorreram nos estágios iniciais de moagem. Em todas as misturas constituídas de pós, os tamanhos de suas respectivas partículas foram aumentados, e a distância entre as lamelas foram reduzidas para longos períodos de moagem. Este fato ocorreu devido ao mecanismo de solda fria entre as partículas dúcteis, que foram totalmente revestidas em suas superfícies esféricas. O rendimento da mistura de Ni-Ti-Mo, Ni-Ti-Ta e Ni-Ti-Mo-Zr aumentou após a moagem molhada. A prensagem a quente contribuiu para a obtenção de estruturas homogêneas e a consolidação dos pós de Ni-Ti-Mo, Ni-Ti-Ta e Ni-Ti-Mo-Zr moídos. No caso das ligas Ni-45Ti-5Mo e Ni-40Ti-10Mo, o composto Ni-Ti foi identificado na estrutura de ambas as ligas, enquanto que as fases Ni3Ti e NiTi2 foram formadas nas microestruturas das ligas Ni-45Ti-5Mo e Ni-40Ti-10Mo. Estas fases intermetálicas dissolveram teores de molibdênio inferiores a 2,1 %-at. Além disso, foi encontrada a presença de precipitados ricos em molibdênio com teores (%-at) próximos de 16Ni-25Ti-59Mo.Não foi encontrada variação significativa dos valores médios de dureza Vickers relacionadas a estas ligas ternárias, após o aumento da...
The Brazil not yet product the Ni – Ti alloy commercially, importing the most products of the Ni-Ti of the medical area. The high cust to wrap up in the importation this products encourage the development national this alloy. In this way, this work aimed the characterization of Ni-Ti-Mo, Ni-Ti-Ta and Ni-Ti-Mo-Zr alloys produced by high-energy ball milling and subsequent hot pressing. The milled and hot-pressed materials were characterized by, scanning electron microscopy, X-ray diffraction, energy dispersive spectrometry. Results indicated that the formation of intermetallic compounds such as Ni3Ti, NiTi and NiTi2 occurred at the initial milling stages. For all the powder mixtures, it was noted that the powder sizes were increased and the distance between lamellas were reduced for longer milling times. This fact occurred due to excessive cold welding mechanism between ductile particles, which were coated fully the vial and balls surfaces. The yield of Ni-Ti-Mo, Ni-Ti-Ta and Ni-Ti-Mo-Zr powders was increased after wet milling. The hot pressing of milled Ni-Ti-Mo, Ni-Ti-Ta and Ni-Ti-Mo-Zr powders contributed for obtainment of homogeneous structures containing amounts of pores lower than 1%. In Ni-45Ti-5Mo and Ni-40Ti-10Mo alloys, the NiTi compound was identified in structure of both the alloys while that the Ni3Ti and NiTi2 were formed in microstructures of the Ni-45Ti-5Mo and Ni-40Ti-10Mo, respectively. These intermetallic phases dissolved molibdenum contents lower than 2.1 at-%. Moreover, it was noted the presence of Mo-rich precipitates with contents close to 16Ni-25Ti-59Mo (at-%). No significant variation of average Vickers hardness values was noted in Ni-Ti-Mo alloys for increased Mo addition up to 10 at-%. In Ni-Ti-Ta alloys, the NiTi and Ni3Ti phases were formed in microstructures of the hot-pressed Ni-48Ti-2Ta and Ni-45Ti-5Ta alloys, while that the Ni3Ti phase was found in ... (Complete abstract click electronic access below)

Descrição

Palavras-chave

Ligas de niquel-titanio, Mechanical alloy

Como citar

PEREIRA, Gilda Maria Cortez. Caracterização das ligas Ni-Ti-Mo, Ni-Ti-Ta e Ni-Ti-Mo-Zr obtidas por moagem de alta energia e prensagem a quente. 2011. 102 f. Dissertação (mestrado) - Universidade Estadual Paulista, Faculdade de Engenharia de Guaratinguetá, 2011.