Survival rate and load to failure of premolars restored with inlays: An evaluation of different inlay fabrication methods

Página do item simplificado
dc.contributor.authorPivetta Rippe, Marília
dc.contributor.authorMonaco, Carlo
dc.contributor.authorMissau, Taiane
dc.contributor.authorWandscher, Vinícius Felipe
dc.contributor.authorVolpe, Lucia
dc.contributor.authorScotti, Roberto
dc.contributor.authorBottino, Marco Antonio [UNESP]
dc.contributor.authorValandro, Luiz Felipe
dc.contributor.institutionUniversidade Federal de Sergipe (UFS)
dc.contributor.institutionUniversity of Bologna
dc.contributor.institutionFranciscan University Center
dc.contributor.institutionUniversidade Estadual Paulista (Unesp)
dc.date.accessioned2019-10-06T15:56:59Z
dc.date.available2019-10-06T15:56:59Z
dc.date.issued2019-02-01
dc.description.abstractStatement of problem: Studies that evaluate the survival rate and load to fracture of premolars restored with inlays produced using different methods are lacking. Purpose: The purpose of this in vitro study was to compare the survival rate and fracture load of premolars restored with inlays fabricated using different methods. Material and methods: Thirty maxillary premolars were selected, embedded, and prepared to receive inlays fabricated using different methods (n=10): LaCom-digital scanning with Lava C.O.S. scanner (3M ESPE), followed by milling of composite resin block (Lava Ultimate; 3M ESPE) in a milling unit; CeCom-digital scanning with Cerec 3D Bluecam scanner (Dentsply Sirona), followed by milling of a Lava Ultimate block in Cerec (Dentsply Sirona); PresDis-impression with polyvinyl siloxane, inlay made using the lost wax technique, and IPS e.max Press (Ivoclar Vivadent AG) pressed ceramic (lithium disilicate). A dual-polymerizing resin cement system was used to lute the inlays. Inlays were mechanically cycled (2 Hz, 106 mechanical pulses, 80 N) after 24 hours, and the specimens were stored in distilled water at 37°C for 11 months. Then, a fatigue test was conducted using a 10-Hz frequency and 400-N load on the inner inclines of the cusps. The test was complete when the specimen fractured or when the specimen reached 1.5×106 cycles. The specimens that survived fatigue testing were submitted to a single-load fracture test in a universal testing machine and analyzed using a stereoscope for failure classification. Survival rates were estimated using the Kaplan-Meier method and log-rank test (Mantel-Cox). Fracture load data were analyzed using 1-way ANOVA (α=.05). Results: No significant differences were detected among the groups for the survival rate (P=.87) or for the load to fracture (P=.78). Most failures were longitudinal, catastrophic fractures. Conclusions: Premolars restored with inlays fabricated using the tested methods had similar survival rates and loads to fracture.en
dc.description.affiliationAdjunct Professor Prosthodontics Unit Faculty of Odontology Federal University of Santa Maria (UFSM)
dc.description.affiliationAssistant Professor and Researcher Department of Biomedical Sciences and Neuromotor Division of Prosthodontics Alma Mater Studiorum University of Bologna
dc.description.affiliationGraduate student Prosthodontics Unit Faculty of Odontology Federal University of Santa Maria (UFSM)
dc.description.affiliationAdjunct Professor Prosthodontics Unit Faculty of Odontology Franciscan University Center
dc.description.affiliationMaster student Department of Biomedical Sciences and Neuromotor Division of Prosthodontics Alma Mater Studiorum University of Bologna
dc.description.affiliationProfessor Department of Biomedical Sciences and Neuromotor Division of Prosthodontics Alma Mater Studiorum University of Bologna
dc.description.affiliationProfessor Dental Materials and Prosthodontics Unit São Paulo State University (UNESP) São José dos Campos
dc.description.affiliationAssociate Professor Prosthodontics Unit Faculty of Odontology Federal University of Santa Maria (UFSM)
dc.description.affiliationUnespProfessor Dental Materials and Prosthodontics Unit São Paulo State University (UNESP) São José dos Campos
dc.format.extent292-297
dc.identifierhttp://dx.doi.org/10.1016/j.prosdent.2018.03.019
dc.identifier.citationJournal of Prosthetic Dentistry, v. 121, n. 2, p. 292-297, 2019.
dc.identifier.doi10.1016/j.prosdent.2018.03.019
dc.identifier.issn0022-3913
dc.identifier.lattes9234456003563666
dc.identifier.scopus2-s2.0-85051043916
dc.identifier.urihttp://hdl.handle.net/11449/188090
dc.language.isoeng
dc.relation.ispartofJournal of Prosthetic Dentistry
dc.rights.accessRightsAcesso aberto
dc.sourceScopus
dc.titleSurvival rate and load to failure of premolars restored with inlays: An evaluation of different inlay fabrication methodsen
dc.typeArtigo
unesp.advisor.lattes9234456003563666

Arquivos

Coleções

Artigos - Materiais Odontológicos e Prótese - ICT